Home     Kontakt     WIAP MEMV      Sprachen     English     News     Neumaschinen     Umbauten

 

             

            

Tubes WIAP® MEMV® relax

 

Photo Gallery Tubes

 

3F) TUBES WIAP® MEMV® RELAX

 

Investigation: Gast special steel pipes are treated  MEMV®

Large pipes

 

k-MEMV_Rohre_dick_Jim_Sven_02

 

Front WIAP® MEMV® device. Back left Jim Peter Widmer, right Sven Widmer.

 

 

k-MEMV_Rohre_dick_Auspannvorricht_Jim01

 

Spanning the workpiece during the serial process of the WIAP® MEMV® process. Rotating top is located on the pallet.

 

 

k-MEMV_Rohre_dick_Auspannvorricht_02

 

Lower part of the rotational biasing means.

 

 

 k-MEMV_Rohre_dick_01

 

WIAP® MEMV® process takes 3 x 12 minutes, 2D, 3D and 4D; 2D = 0°, 45° = 3D and 4D = 90°.

 

 

k-MEMV_Rohre_dick_08

 

WIAP® MEMV® process 2D 0° takes place.

 

 

k-MEMV_Rohre_Steuergeraet_01

 

WIAP® MEMV® controller performs the whole process automatically. Too much G or too much Amperen  reduced Hertz / speed. In outliers that exceed the security zones, the system stops.

 

Small tubes long with dual voltage

 

k-n

 

Here pipes 2 in the double voltage are relaxed.

 

 

k-MEMV_Rohre_duenn_drehen1

 

3D 45° relaxation center position between longitudinal and transverse directions.

 

 

k-MEMV_Rohre_duenn_06

 

4D 90° relaxation, transverse direction, the short axis direction.

 

 

k-MEMV_Rohre_duenn_05

 

2D 0° relaxation, longitudinal direction 0° is always the long axis.

 

 

k-MEMV_Rohre_dick_04

 

WIAP® MEMV® relaxing process takes less than 45 minutes.

 

 

Protocol big part

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Total displacement G, 6.8 (1 G = 9.8 m/ s2) between before and after. For a pipe measured at 36 x before and after points.

 

 

Protocol  small part

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Total G displacement, 61.2 (1 G = 9.8 m/ s2) between before and after. For a pipe measured at 36 x before and after points.

 

 

3G) ASIDES TUBES

 

Thanks to the new WIAP® MEMV® method to determine G shifts between before and after, which are measured at various points.

   

Vertical is the WIAP® MEMV® method, the Y axis. Horizontally and release the X axis and horizontally, the long axis is the Z axis. Always the long axis 2D = 0°, the short axis is 90°.

 

 

A very good alternative to: BONAL MEAT LAX, Formula 62, VSR Vibratory stress relief with vibration. New patented system from Switzerland WIAP MEMV, metal relax .. Unique Process reliability with vibration.

 

Home     Kontakt     Impressum     Seitemap     English     Patente     Neumaschinen     Umbauten